AUTOOL CT80 · 40kHz HEATED ULTRASONIC INJECTOR & PARTS BATH
AUTOOL CT80 Digital Heated Ultrasonic Fuel Injector & Carburetor Cleaner
Strip stubborn carbon deposits and gummed fuel varnish from internal injector passages, carburetor jets, and engine components using 40 kHz ultrasonic micro-implosions and 50°C heated cleaning solution.
- 40kHz Ultrasonic · 60W
- ~50°C Heated SUS304 Tank
- 0–40 Min Timer · 1Y Warranty
Engineered for Professional Workshop Demands
The AUTOOL CT80 is built to deliver speed, accuracy, and durability in busy service bays.
40 kHz Industrial Ultrasonic Transducer
Generates millions of microscopic cavitation bubbles that implode against metal surfaces, dislodging carbon from micro-filters and blind holes without surface damage.
100W Constant-Temperature Heating (~50°C)
Independently switched heating warms the cleaning solution to ~50°C, cutting cleaning time in half on gummed fuel varnish and thick grease.
Seamless SUS304 Tank & Mesh Basket
Constructed from weld-free stamped SUS304 stainless steel with a matching mesh basket that prevents parts from resting directly on the bottom transducer.
0–40 Minute Digital LED Control Panel
Glove-friendly membrane buttons and a bright digital display let you set exact cleaning cycles up to 40 minutes.
AUTOMOTIVE & SMALL ENGINE WORKSHOPS
Restore Injectors, Carburetors & EGR Valves
Aerosol sprays and wire brushes only clean outer surfaces. Ultrasonic cavitation reaches inside microscopic fuel galleries and carburetor emulsion tubes.
- GDI, MPFI, LPG, and diesel injector nozzle & pintle cleaning
- Motorcycle, chainsaw, and small-engine carburetor jet restoration
- Turbo actuator linkages, EGR valves, O2 sensors, and bearings
HEATING + ULTRASONIC SYNERGY
50°C Heated Solution Melts Baked-On Deposits
Cold ultrasonic baths struggle with solidified grease. Engaging the CT80's heater activates water-based degreasers for rapid carbon removal.
- Independent Ultrasonic and Heating toggle buttons
- 150 × 135 × 100 mm basin holds 4–6 fuel injectors simultaneously
- Non-slip rubber feet and stainless steel sound-dampening lid
MULTI-PURPOSE BENCH TOOL
From Fuel Systems to PCB Boards & Hardware
Compact enough for any technician's workbench while built to industrial standards.
- 220V AC plug-and-play operation with thermal safety protection
- Lightweight 1.95 kg footprint
- Backed by a 1-year official Otoeko warranty
Detailed Visual & Technical Infographic Showcase
Close-up hardware details and application scenes of the AUTOOL CT80.
Technical Specifications & Hardware Parameters
Complete manufacturer-verified technical data and operating ranges.
| Brand / Model | AUTOOL CT80 Digital Heated Ultrasonic Cleaner |
|---|---|
| Ultrasonic Frequency & Power | 40 kHz · 60W Industrial Transducer |
| Heating Power & Temp | ~100W · ~50°C Constant Thermal Heating |
| Tank Capacity | 1600 ml – 2000 ml (1.6L Nominal Volume) |
| Tank Material | SUS304 Stainless Steel (Seamless Stamped) |
| Timer Setting | 0 – 40 Minutes Digital LED Countdown |
| Inner Tank Dimensions | 150 × 135 × 100 mm |
|---|---|
| Outer Unit Dimensions | 175 × 165 × 200 mm |
| Net Weight | 1.95 kg |
| Power Supply | AC 220V · 50/60 Hz |
| Included Accessories | SUS304 Mesh Parts Basket & Stainless Lid |
| Warranty | 1 Year Official Otoeko Warranty |
Workshop Application & Operating Guide
Recommended 4-step standard operating procedure for accurate results.
Fill with Cleaning Solution
Fill the stainless tank 2/3 full with water and water-based ultrasonic injector/parts cleaning detergent (never run dry).
Load Parts into Basket
Place injectors or carburetor parts inside the stainless mesh basket so they do not rest directly on the tank floor.
Activate Heat & Timer
Turn on Heating for greasy parts, set the digital timer (15–30 min), and start Ultrasonic cavitation.
Rinse & Blow Dry
Remove the basket once the timer finishes, rinse parts with clean water, and blow dry with compressed air.
Conventional Methods vs. Professional Diagnostics
How precision engineering eliminates guesswork and comebacks.
Conventional / Basic Methods
- Brushes and sprays cannot reach inside blind carburetor jets or injector tips
- Unheated ultrasonic cleaners fail to dissolve thick oil and fuel varnish
- Thin metal tanks corrode quickly when exposed to degreasers
- Mechanical dial timers lack precision and wear out quickly
With AUTOOL CT80
- 40 kHz cavitation cleans inside microscopic internal fuel passages
- ~50°C built-in heater doubles degreasing and carbon-removal speed
- Heavy-gauge SUS304 stainless tank resists workshop chemicals
- 0–40 minute digital LED timer with stainless parts basket included
Package Contents — Ready for the Workshop
Complete factory kit inspected prior to dispatch.
- 1 × AUTOOL CT80 Digital Heated Ultrasonic Cleaner
- 1 × SUS304 Stainless Steel Mesh Basket & Stainless Lid
- 1 × 220V Power Cord & User Manual
1 Year Official Otoeko Warranty
The AUTOOL CT80 is backed by a 1 Year official Otoeko warranty against manufacturing defects, with full technical support.
Frequently Asked Questions
Key technical questions from technicians and workshops about the AUTOOL CT80.
What liquid should I use in the tank?
Use water mixed with a water-based ultrasonic parts or injector cleaning concentrate. Never use flammable solvents such as gasoline, brake cleaner, or lacquer thinner.
How many fuel injectors fit at once?
The 150 × 135 × 100 mm tank easily accommodates 4 to 6 petrol or diesel injectors in the basket.
Will motorcycle and small-engine carburetors fit?
Yes, motorcycle, ATV, chainsaw, and generator carburetors fit comfortably inside the basin.
Can I run the ultrasonic cleaner without liquid?
Never run the unit dry—always ensure liquid covers at least half to two-thirds of the tank before switching on Heat or Ultrasonic.
Can I use Ultrasonic without turning on Heating?
Yes, the Heating and Ultrasonic buttons operate independently.
What is the warranty period?
It comes with a 1-year official Otoeko warranty.