SCANIA VCI 3 · P/N 2405302 · SDP3 & XCOM/SOPS READY
Scania VCI 3 Heavy-Duty Truck, Bus & Marine Engine Diagnostic VCI
Replacing the legacy VCI 2, the Scania VCI 3 combines high-speed CAN-Bus architecture with built-in Wi-Fi and USB connectivity to diagnose, calibrate, and program every electronic control module on modern Scania fleets.
- Scania SDP3 & XCOM Ready
- Euro 3 / 4 / 5 / 6 & NTG
- Wireless Wi-Fi + USB
- 6-Month Otoeko Warranty
Engineered for Professional Workshop Demands
The Scania VCI 3 (Vehicle Communication Interface 3 · Wi-Fi + USB) is built to deliver speed, accuracy, and stability in busy service bays.
Complete Access to All Scania ECUs
Scans EMS (Engine), GMS (Opticruise), EBS (Brakes), APS (Air Processing), COO (Coordinator), ICL (Instrument Cluster), LAS, and EEC (SCR/Aftertreatment).
Opticruise Gearbox & ECA Clutch Calibration
Performs clutch kiss-point and gear synchronization calibrations after ECA actuator or clutch replacement.
Engineering-Level XCOM & SOPS Support
Works with Scania XCOM and SOPS tools to read/write SOPS files, edit VINs, reset immobilizers, and configure chassis parameters.
Wireless Wi-Fi & Extruded Aluminum Housing
Durable anodized aluminum enclosure with strain-relieved OBD2 harness and built-in WLAN module.
ENGINE, FUEL & AFTERTREATMENT
Deep Diagnostics for PDE, HPI & XPI Common Rail Engines
Covers Scania DC09, DC11, DC12, DC13, and DC16 V8 engines:
- XPI and PDE injector IMA coding, compression testing, and cylinder cut-out tests
- VGT turbocharger actuator calibration and rail pressure regulation tests
- DPF service regeneration, ash counter reset, and EEC3/SCR AdBlue pump testing
- Industrial generator and marine engine (DI09, DI13, DI16) parameter configuration
TRANSMISSION, BRAKES & COORDINATOR (COO)
Opticruise, Retarder, APS & COO7/COO8 Programming
Executes dealer-level service routines across powertrain and chassis modules:
- COO7 and COO8 coordinator replacement backup, cloning, and immobilizer pairing
- Opticruise (GMS) ECA clutch actuator calibration and Scania Retarder testing
- APS air dryer cartridge reset and circuit pressure calibration
- EBS brake modulator and ELC air suspension ride-height calibration
WIRING DIAGRAMS & GUIDED DIAGNOSTICS
Interactive Schematics & Component Locations Inside SDP3
Speeds up electrical troubleshooting directly from fault codes:
- Interactive wiring diagrams and connector pin-outs linked directly to active DTCs
- VIN-specific SOPS factory configuration readout and spare part verification
- Maintenance interval resets, operating data extraction, and PDF report export
- Stable data transfer via Wi-Fi or high-speed USB 2.0
Detailed Visual & Technical Showcase
Close-up details and application views of the Scania VCI 3 (Vehicle Communication Interface 3 · Wi-Fi + USB).
Technical Specifications & System Parameters
Complete manufacturer-verified technical data and operating ranges.
| Hardware Model | Scania VCI 3 (Vehicle Communication Interface 3) |
|---|---|
| Reference P/N | 2405302 |
| Compatible Software | Scania SDP3 (2.48 – 2.60+), Scania XCOM, SOPS Editor |
| Vehicle Coverage | 2004+ Scania P, G, R, T, Next-Gen S/R/G/P/L & F/K/N Buses |
| Connectivity | Wireless Wi-Fi (802.11 b/g/n) + High-Speed USB 2.0 |
| Supported Protocols | High-Speed CAN (ISO 11898), KWP2000, SAE J1939 |
| Housing Material | Anodized Aluminum with Rubber End Caps |
|---|---|
| Operating Voltage | 24V DC Commercial / Marine Systems (12V–30V Range) |
| Status LEDs | 5 Indicators (Power, CAN, USB, WLAN, Error) |
| OS Compatibility | Windows 10 & Windows 11 (64-Bit) |
| Origin | China (Industrial Grade A+ PCB & Wi-Fi Module) |
| Warranty | 6-Month Official Otoeko Warranty |
Workshop Application & Operating Guide
Recommended 4-step standard procedure for accurate results.
Connect to OBD2 Port
Plug the integrated 16-Pin OBD2 connector into the cabin diagnostic socket.
Pair via USB or Wi-Fi
Connect the VCI 3 to your laptop via USB or wireless WLAN and switch the ignition ON.
Scan SOPS & ECUs in SDP3
Launch Scania SDP3 to automatically read the vehicle SOPS file and scan all control units.
Calibrate & Configure
Clear fault codes, run Opticruise/APS calibrations, or modify parameters via XCOM.
Technical Capabilities & Operational Advantages
Key engineering advantages for professional workshop diagnostics.
Core Workshop Requirements
- Legacy VCI 2 interfaces do not fully support 2016+ Next-Gen (S/R) Euro 6 Scania trucks.
- Generic scanners cannot perform COO7/COO8 pairing, APS resets, or ECA clutch calibration.
- Cannot read/write encrypted SOPS files or run Scania XCOM engineering functions.
- No integrated interactive wiring diagrams or component location views.
With Scania VCI 3 (Vehicle Communication Interface 3 · Wi-Fi + USB)
- 100% SDP3 compatibility across all 2004–present P/G/R/T and Next-Gen S/R Euro 6 vehicles.
- Performs Opticruise ECA clutch, APS air dryer, and COO7/COO8 coordinator routines.
- Fully compatible with Scania XCOM and SOPS Editor for advanced parameter changes.
- Dual Wi-Fi + USB connectivity in a rugged anodized aluminum housing.
Package Contents — Ready for the Workshop
Complete kit inspected prior to dispatch.
- 1 × Scania VCI 3 (P/N 2405302) Main Diagnostic Unit with Integrated OBD2 Cable (Wi-Fi + USB)
- 1 × High-Speed USB PC Cable
- 1 × Protective Storage Box (Note: SDP3/XCOM software not included, sold separately)
6 Months Official Otoeko Warranty
The Scania VCI 3 (Vehicle Communication Interface 3 · Wi-Fi + USB) is backed by a 6 Months official Otoeko warranty against manufacturing defects, with full technical support.
Frequently Asked Questions
Key technical questions from technicians and workshops about the Scania VCI 3 (Vehicle Communication Interface 3 · Wi-Fi + USB).
Which Scania models and years are supported?
Supports all 2004–present Scania P, G, R, T trucks, 2016+ Next-Gen (NTG) S, R, G, P, L series, F/K/N buses, and industrial/marine engines.
Does it support pre-2004 Scania 3 and 4 series?
No, pre-2004 3/4-series vehicles use VCI 1 with SD2/SP2; VCI 3 is designed for 2004+ CAN-Bus vehicles.
Can it calibrate Opticruise clutches and pair COO7/COO8?
Yes, via SDP3 and XCOM it performs Opticruise ECA calibration, APS resets, and COO7/COO8 pairing.
Does it have built-in Wi-Fi?
Yes, our A+ hardware includes an active internal Wi-Fi module alongside USB connectivity.
Is SDP3 software included?
This listing is for the VCI 3 hardware; software and turnkey laptop bundles are available separately.
What is the warranty period?
Backed by a 6-month official Otoeko hardware warranty.